FREE TOOLS. ZERO LIMITS.
No Signup RequiredNo Watermarks
ToolzNova ยท Lab calculators

Disinfectant Dilution Calculator Online

Mix disinfectant concentrate at the label ratio for any bottle or bucket, and see the in-use strength of the active ingredient in percent and ppm.

Disinfectant Dilution Calculator

Free disinfectant dilution calculator that runs in your browser. Nothing is uploaded.

% and ppm

Strength and contact time on the label are both needed for the claimed kill rate.

How to dilute disinfectant

1Enter the label ratio

For example 1:100 or 1:256.

2Enter the volume and active %

Active % comes from the label.

3Mix and observe contact time

Leave surfaces wet for the time stated.

In-use strength from a 10% concentrate

In-use % = active % รท (x + 1).

Values for a concentrate with 10% active ingredient.

RatioProduct per litreIn-use strengthppm
1 : 6415.4 mL0.154%1,538 ppm
1 : 1009.9 mL0.099%990 ppm
1 : 2563.9 mL0.039%389 ppm
1 : 4002.5 mL0.025%249 ppm

Mixing disinfectant correctly

This short guide explains what the disinfectant dilution calculator does, how to get the best result and when another tool is a better fit.

Why strength matters

Disinfectants are tested and approved at a specific dilution and contact time. Below that strength they may not kill the organisms claimed on the label; above it they can damage surfaces, leave residue and expose staff to more chemical than needed. Accurate dilution is therefore a safety and compliance issue, not just a cost one.

Disinfectant Dilution Calculator โ€“ 1 : x to ppm
How the disinfectant dilution calculator works: 1 : x in, ppm out.

Follow the label ratio, not guesswork.

In-use concentration

Enter the percentage of active ingredient in the concentrate, such as quaternary ammonium compounds, and the calculator shows the in-use strength in percent and ppm. Many food-contact sanitising rules and test strips use ppm, so this lets you check a mix with strips. For example, a 10% quat at 1:256 gives about 390 ppm.

Test strips confirm the strength in the bucket.

A worked example

A clinic uses a disinfectant labelled 1:100 for hard surfaces. For a 1 L spray bottle, thatโ€™s 9.9 mL concentrate and 990 mL water. With 10% active ingredient, the in-use solution is 0.099%, about 990 ppm. For a 4 L bucket at 1:256, itโ€™s 15.6 mL, giving about 390 ppm.

Write the mix date on the bottle.

Safety and contact time

Clean visible dirt first, as soil reduces disinfectant effect. Keep surfaces wet for the full contact time on the label. Wear gloves and eye protection when handling concentrate, ensure ventilation, and never mix disinfectants with bleach, acids or other cleaners. Discard diluted solutions after the time the label allows.

Food-contact surfaces may need a rinse or a no-rinse rated product.

Related tools

For chlorine bleach, use the Bleach Dilution Calculator. For food sanitisers, use the Sanitizer Dilution Calculator.

  • In-use % = active % รท (x + 1)
  • ppm = % ร— 10,000
  • Respect the contact time

Further reading: About disinfectants. It explains the format behind this disinfectant dilution calculator in more detail.

Where it helps

Healthcare

Surface disinfection.

Food service

Sanitising.

Schools and gyms

Shared surfaces.

Veterinary

Kennels and clinics.

Quick fixes

โ€œโ€ฆmore than 1 : 1โ€

With the total-parts method, use a ratio above 1.

Test strip reads low

Old solution or wrong ratio; remix.

No active % on label

Leave that box blank.

Surfaces sticky

Too strong, or needs a rinse.

Frequently asked questions

How do I dilute disinfectant?

Enter the label ratio and volume.

What is 1:100?

1 part concentrate to 100 parts water.

How much for 1 L at 1:100?

About 9.9 mL.

What ppm is a 10% quat at 1:256?

About 390 ppm.

How do I calculate in-use strength?

Active % รท (x + 1).

What is contact time?

How long the surface must stay wet.

Can I make it stronger?

Only if the label allows.

Can I mix with bleach?

No.

Is my data saved?

No.

Is it free?

Yes.