FREE TOOLS. ZERO LIMITS.
No Signup RequiredNo Watermarks
ToolzNova · Audio Editing

Audio Trimmer Online

Cut the part of an audio recording you actually need. Select a start and end time, listen to your choice, and export a new MP3 or WAV clip without changing the source file.

Choose precise timestampsMP3 or WAV outputLocal browser processing
Trim an audio file
AudioSource file
ClipMP3 / WAV
01Upload audio
02Select segment
03Export clip

Audio Trimmer — Select Your Clip

Listen first, choose the cut points, then export a separate audio file.

One file at a time
No file selected. A source preview is shown when your browser supports its format.
Selected clip: 10.0 seconds. The file size depends on duration, output format and encoding settings.
The audio engine downloads when you trim. This may take longer on the first use.
Your trimmed audio is readyDownload trimmed clip

A simple editing workflow

How to trim an audio file in three steps

Every control is meant to answer one question: what is the source, which moment do you need, and how should the new clip be saved?

01

Choose a recording

Select a supported audio file. Use the player to find the point at which the useful sound begins. The file stays on your device while this page processes it.

02

Mark the exact range

Enter a start and end time in seconds, or play the source and capture its playhead position. The end must be later than the start and within the recording.

03

Review your new clip

Choose MP3 or WAV, press Trim audio and listen to the generated result. Download it only after checking the boundaries and sound level.

Purpose before format

Choose an output that fits your next task

Trimming is a time-based edit. Changing the format is a separate decision, so the tool offers two straightforward ways to save the selected segment.

MP3 — practical sharing copy

An MP3 clip is useful for messages, lesson extracts, podcast samples and apps that expect a familiar audio format. A lower bitrate generally creates a smaller file, with more potential quality loss. If your original source is already MP3, this workflow encodes it again, so do not treat the result as lossless.

WAV — uncompressed editing copy

Choose PCM WAV when another editing program expects an uncompressed audio file. WAV can be much larger than MP3 for the same duration. Converting a lossy source to WAV does not recover details that its earlier codec discarded. Keep the source recording for future edits whenever possible.

Editing guidance

Finding a clean start and finish

Good audio editing is as much about listening as about entering timestamps. The Audio Trimmer can cut a ten-second quotation from a longer interview, but it cannot decide whether the first spoken syllable has been clipped. Listen just before the intended start, then leave a short lead-in when the audio begins with a breath, consonant or musical attack.

If a sound fades gradually, leave a little more room at the end. A cut made at an arbitrary instant can sound abrupt even though the new file is valid. For speech, check whether the last word finishes naturally. For music or ambient recordings, place the endpoint during a quiet passage when practical. This tool creates a selected clip; it does not automatically add fades, noise reduction or loudness normalization.

Use the source player's time counter to inspect a recording. Enter seconds directly when you know the timing: 1 minute 15 seconds becomes 75 seconds. For a clip beginning at 75 and ending at 92.5, the selected duration is 17.5 seconds. Start and end controls use seconds rather than a confusing mixture of minutes and timestamps.

Real editing situations

Where a short audio clip helps

Different recordings need different boundaries. These examples show practical decisions rather than claiming a single setting works everywhere.

♪

Lecture highlight

A student needs a 25-second explanation from a long recording. Start slightly before the lecturer introduces the idea, end after the final sentence, and use MP3 for convenient playback on a phone. Keep the original recording in case more context is needed.

●

Voice-message excerpt

Remove the silence preceding a voice note. A 0.5-second margin may sound more natural than cutting exactly at the first visible audio peak. Export a separate clip and replay it to ensure the first word is understandable.

▥

Podcast editing handoff

Extract a guest's answer for an editor to review. If the editing system prefers WAV, save a PCM copy. That makes the clip easy to import, but does not improve the sound quality of a previously compressed source.

ExampleStartEndLength
Remove a spoken introduction6.0 s18.5 s12.5 s
Save a short quotation75 s92.5 s17.5 s
Extract a musical phrase33.2 s45.2 s12 s

Technical transparency

What this audio trimmer can and cannot do

When you run the converter, the browser loads FFmpeg WebAssembly and decodes the selected audio. It then creates a new file from the requested interval. MP3 output uses an MP3 encoder; WAV output uses 16-bit PCM. The output is a fresh file rather than an in-place change to your upload.

Browser decoding and file formats have limits. An audio player might be unable to preview a particular FLAC, AAC or Ogg file even when FFmpeg can read it; in that case, entering the start and end values manually may still allow conversion. Protected media, corrupted files, invalid audio tracks and unusually large recordings can fail. A file extension alone cannot guarantee a valid recording.

Because re-encoding changes the sound data, output size is not directly proportional to the time removed. A ten-second WAV export may be larger than an already compressed ten-second MP3. Encoding can also alter metadata such as tags or cover art, so the clipped file should not be treated as an archive copy. Keep the original unchanged until the exported clip plays correctly.

?

Troubleshooting a failed export

Library won't load: Verify internet access and allow the FFmpeg script to load. The first use needs an external library download.

No audio in the result: Check that the source actually contains a readable audio stream, and that your range does not fall outside the recording.

Memory or slow processing: Try a shorter source or desktop browser. Large files can exhaust device memory; this tool is intended for short or moderate recordings rather than bulk jobs.

Clip cuts too early: Shift the start point backward slightly and run again from the original.

Continue your workflow

These pages do different jobs. Choose the one that solves your next problem, rather than following unrelated links.

Keep internal navigation purposeful: an audio trimmer cuts by time, a compressor changes encoding or size, and a converter changes the format. None of these tools automatically fixes bad microphone quality.

Helpful answers

Audio Trimmer FAQs

Answers about timing, supported audio formats, quality and processing limits.

Can I cut just a few seconds from an MP3?

Yes. Enter the start and end time in seconds. A range from 12.5 to 18.0 creates approximately 5.5 seconds of output. Listen to the result, because encoding and playback can affect boundary perception.

Does trimming lower audio quality?

This tool encodes a new file. Saving as MP3 adds lossy compression even if the original was already MP3. Choose a higher MP3 bitrate when quality matters, or WAV for an uncompressed PCM output; WAV does not recover information lost earlier.

Can I preview the audio before cutting?

The source player works when your browser supports the file's format. You can play the selection using your chosen timestamps. If the browser cannot preview that format, try entering the range manually and exporting with FFmpeg.

Why is my trimmed WAV bigger than the original MP3?

WAV PCM is typically uncompressed while MP3 removes information to reduce size. Even a shorter WAV can use more storage. Export MP3 when you need a smaller delivery copy rather than a PCM editing file.

Will an uploaded file be sent to a conversion server?

The tool's conversion JavaScript uses FFmpeg WebAssembly in the browser, rather than submitting the source file to a dedicated conversion endpoint. The page still fetches external code and may use unrelated site services, so this is not a blanket privacy guarantee.

What if the audio has no known duration?

Some audio containers do not expose duration to the browser's native player. Enter the estimated start and end seconds manually. Conversion can still fail if the requested range falls beyond the actual playable material.

Can I join multiple clips or fade audio in this tool?

No. The tool trims one continuous segment from one source file. Joining clips, fades, noise repair, loudness matching and multitrack editing require a dedicated audio editor.